RCP RC Motors Castle 2028 Series 800kv-1100kv-1700kv EXTREME Motors

Welcome to our E b a y store We specialize in  RC Power Products  such as ESC's, motors,  and wiring accessories.  Along with  QS8 Connectors & Accessories! We sell the best selection of esc mount plates available! Check out our m ounts that fit Traxxas X Maxx, XRT,  & Maxx Trucks! Fit Arrma Kraton/Outcast 6s & 8s Trucks! And try our  8 volt  28 cfm 4028 Super  High Speed Fans NO MORE NEED for 3s or 4s extra batteries in your car to run the cooling fans!! Just plug into  the receiver for high speed fans!   WE COMBINE SHIPPING! 1 Reduced shipping charge when checking out with multiple items! We are Authorized Dealers for Castle Creations & Hobbywing Listed item Specifics: 2028 Size Castle Creations Motors BRAND NEW IN SEALED PACKAGE All 8mm Bullet Connectors On Motor Wires We are Authorized  Castle Creations ReSellers!! Choose: 2028 800kv 2028 1100kv 2028 1700kv (Extreme) We include 300 RC Zip Ties In Green 5 1/2" Long Better Flexibilty Easier to use We offer all these motors with esc's in combos Ready to Run Connectors Attached in separate listings 2028 800kv Technical Specs Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Size: Length: 4.4" (112.7mm) Diameter: 2.2" (56.3mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm @ 30mm Cooling Fan: Use the RCP Xtreme Cool 56mm motor bracket with (2) 4010 or preferrably if you have the space use our 4028 8v SUPER FANS!! Connectors: 8.0mm male connectors, 250mm sensor wire. Items Needed for Operation: XLX2 esc which RCP offeres RTR in separate listings Product Use Statements: Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the the motor or ESC. Do not use mounting screws that extend more than 5mm into the front of the motor. Using too long of a screw can result in damage to the motor's windings and will not be covered by the warranty. Application Guidelines:
Perfect upgrade for any 1:5 scale RC hobby vehicles (including gas to electric conversions) weighing up to 30 lbs for 2WD and 25 lbs for 4WD Recommended ESC(s): XLX2 Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. Tech Notes:
Running modes: Sensorless and Sensored
The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. We recommend applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. 2028 1100kv Technical Specs Input Voltage Range: 10S MAX Kv: 1100 Max. RPM: 45,000 Size: Length: 4.4" (112.7mm) Diameter: 2.2" (56.3mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 0.315" (8mm) Mounting Hole Specifications: 4mm @ 30mm Cooling Fan: Use the RCP Xtreme Cool 56mm motor bracket with (2) 4010 or preferrably if you have the space use our 4028 8v SUPER FANS!! Connectors: 8.0mm male connectors, 250mm sensor wire. Items Needed for Operation: XLX2 esc which RCP offeres RTR in separate listings Product Use Statements: Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the the motor or ESC. Do not use mounting screws that extend more than 5mm into the front of the motor. Using too long of a screw can result in damage to the motor's windings and will not be covered by the warranty. Application Guidelines: The 2028-1100KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. We recommend applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. 2028 EXTREME 1700kv Technical Specs Input Voltage Range: 8S MAX Kv: 1700 Max. RPM: 60,000 Size: Length: 4.4" (112.7mm) Diameter: 2.2" (56.3mm) Weight (w/wires): 44.9 oz./1.25kg Shaft Size: Length: 30mm Diameter: 0.315" (8mm) Mounting Hole Specifications: 4mm @ 30mm Cooling Fan: Use the RCP Xtreme Cool 56mm motor bracket with (2) 4010 or preferrably if you have the space use our 4028 8v SUPER FANS!! Connectors: 8.0mm male connectors, 250mm sensor wire. Items Needed for Operation: XLX2 esc which RCP offeres RTR in separate listings Product Use Statements: This is an extremely powerful motor designed for advanced and experienced users only. Below are suggestions for increasing your likelihood of success but it is not guaranteed. Start with very conservative gearing (small pinion/large spur). Check your data logs, temperatures and setup closely after each run to ensure you are not stressing components. This motor is intended for single passes only; allow time between runs for the ESC, batteries and motor to cool down to ambient temperatures. This motor can pull very high amperages. Make sure your batteries, connectors and soldering are capable of handling the loads. Inadequate power can cause poor performance and damage the batteries and/or ESC. Do NOT free rev the motor with no load, particularly when running 6s or higher. The RPM output of the motor is much higher with no load as the kv and battery voltages do not drop. Set ESC timing to Lowest (0). This motor will pull considerably more amperage as you increase timing. This does not necessarily equate to more speed as it puts more strain on the batteries and causes the voltage to sag. Less is more sometimes. Do not exceed 33.6v when using this motor. Be sure your pinion and motor bullets are secure before and after each run Recommended ESC(s): XLX2 esc which RCP offeres RTR in separate listings Running Modes: SmartSense™ (with Castle Sensor capable ESC), Sensored and an ultra-efficient Sensorless mode. Tech Notes: Water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. We recommend applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. We Combine on Shipping Hit "Save This Seller" We are adding cool new items in our store for RC! Thank You for your business!